四川君见玮贸易有限公司
Sichuan Junjianwei Trading Co.
扎丝_扎丝生产厂家电话_镀锌扎丝厂家电话_君见玮辅材生产厂家
JUNJIANWEI
扎丝
Tie wire
产品图片
Product image
产品适用方案
Product applicability plan
Selection and Use of Steel Bar Binding Wire
一、选择合适的扎丝粗细 在进行钢筋绑扎时，需要选择合适的扎丝粗细。一般来说，钢筋的直径越大，需要使用的扎丝直径也越大。常见的扎丝直径为0.8mm、1.0mm、1.2mm等规格，一般建议使用1.0mm左右的粗细，能够保证扎紧程度，也不会过于粗细影响扎丝效果。
二、掌握正确的扎丝方法 正确的扎丝方法可以保证钢筋之间的连接紧密牢固。具体操作步骤如下： 1.准备好需要绑扎的钢筋，固定住其中一根; 2.将扎丝放置在需要绑扎的位置，先扎紧一端; 3.将另一端绕过钢筋另一侧，再穿回扎丝，用力拉紧; 4.剪掉多余的扎丝。 在使用扎丝时，需要注意的是，每根钢筋的扎丝数量要符合要求，过少会影响连接牢固程度，过多浪费时间和材料。
三、注意安全工作 在进行钢筋绑扎时，要注意安全工作，避免扎丝过程中手部被钢筋刮伤或者扎丝不牢固导致危险情况的发生。在选购扎丝时，要选择有质量保证的产品，避免质量不佳影响工作效率。
四、保护环境 施工过程中应该注重环境保护，将废弃的扎丝及时清理，避免扎丝材料对环境造成污染。
【结论】 选择正确的扎丝粗细和操作方法可以保证钢筋绑扎牢固，从而确保建筑工程的质量和安全，同时在进行施工工作时，也需要注意安全工作和环境保护。
1、 Choose the appropriate binding thickness
When binding steel bars, it is necessary to choose the appropriate thickness of the binding wire. Generally speaking, the larger the diameter of the steel bar, the larger the diameter of the tie wire that needs to be used. Common wire tie diameters include 0.8mm, 1.0mm, 1.2mm, and other specifications. It is generally recommended to use a thickness of about 1.0mm to ensure the tightness and not affect the wire tie effect.
2、 Mastering the correct wire tying method
The correct wire binding method can ensure a tight and firm connection between the steel bars. The specific operation steps are as follows:
1. Prepare the steel bars that need to be bound and fix one of them;
2. Place the tie wire in the position where it needs to be tied, and first tie one end tightly;
3. Wrap the other end around the other side of the steel bar, thread back the binding wire, and tighten it with force;
4. Cut off excess tie wire.
When using tie wires, it should be noted that the number of tie wires for each steel bar should meet the requirements. If there is too little, it will affect the firmness of the connection and waste time and materials.
3、 Pay attention to safety work
When binding steel bars, it is necessary to pay attention to safety work and avoid dangerous situations caused by scratches on the hands of the steel bars or unstable binding during the binding process. When choosing tie wire, it is important to choose products with quality assurance to avoid poor quality affecting work efficiency.
4、 Protecting the environment
During the construction process, attention should be paid to environmental protection, and discarded wire ties should be promptly cleaned to avoid environmental pollution caused by wire tie materials.
Conclusion
Choosing the correct wire thickness and operation method can ensure that the steel bars are firmly bound, thereby ensuring the quality and safety of the construction project. At the same time, safety work and environmental protection also need to be paid attention to during construction work.
ensure the smooth progress of each construction process. According to the erected position, it is divided into external scaffold and internal scaffold; According to different materials, it can be divided into wood scaffolding, bamboo scaffolding, and steel pipe scaffolding; According to the structural form, it is divided into upright scaffolding, bridge scaffolding, portal scaffolding, suspended scaffolding, hanging scaffolding, cantilever scaffolding, and climbing scaffolding.
the structural form, it is divided into upright scaffolding, bridge scaffolding, portal scaffolding, suspended scaffolding, hanging scaffolding, cantilever scaffolding, and climbing scaffolding.
如您有意咨询请给我们君见玮致电
我们期待您的来电！
If you are interested in consulting, please call us Jun Jianwei We look forward to your call!
咨询电话：18733020585 18508222730
Consultation hotline
止水螺杆使用时的安装间距
我们知道止水螺杆普遍的操作方法是木模板或复合型模版时选用，止水螺杆这一在标准里〈施工工艺〉的规定是常见间隔在400~600，实际的间隔，应当看施工计划设计方案上的要求，由于有的的地区施工单位墙的薄厚非常后，这类状况下止水螺杆间隔就规定就大。实际间隔牵涉到止水螺杆的应用直径、框架柱的高宽比，再开展实际的测算就可以得到。
We know that the common operating method for water stop screws is to use wooden templates or composite templates. In the standard “Construction Technology”, the spacing for water stop screws is usually between 400 and 600. The actual spacing should depend on the requirements of the construction plan design scheme. Due to the extremely thin thickness of the construction unit wall in some areas, the spacing for water stop screws is specified to be large in such situations. The actual spacing involves the application diameter of the water stop screw and the aspect ratio of the frame column, which can be obtained by conducting actual calculations.
pvc管材安装使用方法
PVC管材的安装方法： 1，PVC管在与钢管连接的时候，要先将钢管的连接处擦胶水，将PVC管加热后变软不会烧焦，然后承插在钢管上做降温处理。 2，粘接的时候严禁沾到水，PVC管必须放平在沟内，接头24小时后开始回填，要将管道的四周填紧，接头部位大批量回填。 3，玻璃纤维固化剂配成的树脂溶液浸渍玻璃纤维布之后，均匀缠绕在管道的渗漏出然后固化形成玻璃钢。 4，套补粘接法主要是针对管道小孔和接头的渗漏，选用统一的口径管材将其纵向剖开，然后将管内和外表面打毛，涂胶后在漏水处贴紧。
Installation method of PVC pipes:
1. When connecting PVC pipes to steel pipes, the joints of the pipes should be rubbed with glue first, and the PVC pipes should be heated to become soft without burning. Then, they should be inserted onto the steel pipes for cooling treatment.
2. During bonding, it is strictly prohibited to touch water. PVC pipes must be placed flat in the trench, and backfilling should begin 24 hours after the joint. The surrounding areas of the pipeline should be filled tightly, and the joint parts should be backfilled in large quantities.
3. After the resin solution prepared with glass fiber curing agent is impregnated with glass fiber cloth, it is evenly wrapped around the leakage of the pipeline and then solidified to form fiberglass.
4. The patching and bonding method is mainly aimed at the leakage of small holes and joints in the pipeline. A unified caliber pipe material is selected to longitudinally cut it open, and then the inner and outer surfaces of the pipe are roughened. After applying glue, it is tightly adhered to the leaking area.
钢筋连接套筒和钢筋接头的使用安装方法
一、钢筋连接套筒和钢筋接头的使用安装 1、钢筋就位：将丝头查验合格的钢筋搬运至待联接处。 2、接头拧紧：运用扳手或管钳等东西将联接接头拧紧。 3、作符号：对现已拧紧的接头作符号，与未拧紧的接头区分隔。 4、施工查验：对施工完的接头进行的质量查验。 5、绑扎其它钢筋。 钢筋接头加工的技术是需要十分慎重的进程需要的，我们可以经过比较其他加工技术而言，钢筋接头的技术进程是十分慎重的。
1、 Use and installation of steel bar connection sleeves and steel bar joints 1. Steel bars in place: Transport the steel bars that have passed the wire head inspection to the joint to be connected. 2. Joint tightening: Use a wrench or pipe wrench to tighten the joint. 3. Mark: Mark the joints that have been tightened and separate them from the area of the joints that have not been tightened. 4. Construction inspection: Quality inspection of joints after construction. 5. Bind other steel bars. The technology of processing steel bar joints requires a very cautious process, and we can compare it with other processing technologies. The technical process of steel bar joints is very cautious.
钢筋马镫是做什么用的？
一、提高施工质量 铁马凳的采用，对建筑施工来说，是一种施工技术，因产品为工厂标准化、规格化生产，故其质量比人工制作的马镫更为标准，更加控制板楼下层钢筋保护层的标准性，并有效控制了上下层钢筋的间距。而且通过支架的使用，便于工地施工管理的规范，减少施工随意性。 二、提高施工效率 与传统人工工地现场制作的马镫相比，铁马凳因产品轻巧，安装简便，易于定位，从而减小施工人员劳动强度，通过实际使用情况测算，平均提高现场钢筋施工效率20%左右，在加快了钢筋混凝土施工进度的同时降低了施工成本。并且减少了工地的焊接，有利于提高项目施工的安全性。 三、降低施工成本 铁马凳的使用不仅有效控制工地废料的产生（包括工人现场制作马镫的认为损耗），而且减少了工人现场加工量，节约了工地现场用电量，很大程度降低了生产成本。并且我公司的产品价格比施工现场所用废钢筋制作的铁马凳节约成本30%左右，比用成品钢筋制作的马镫节约成本50%左右，直接降低施工成本。
1、 The use of iron horse stools to improve construction quality is a construction technology for building construction. As the product is standardized and produced by the factory, its quality is more standardized than that of manually made stirrups, which better controls the standardization of the protective layer of the lower steel bars in the slab building and effectively controls the spacing between the upper and lower steel bars. Moreover, the use of brackets facilitates standardized construction management on the construction site and reduces the randomness of construction. 2、 Compared with traditional manual on-site production of stirrups, the iron horse stool reduces the labor intensity of construction personnel due to its lightweight, easy installation, and easy positioning. Based on actual usage, it increases the on-site steel bar construction efficiency by an average of about 20%, accelerating the progress of reinforced concrete construction and reducing construction costs. And it reduces welding on the construction site, which is beneficial for improving the safety of project construction. 3、 The use of iron horse stools to reduce construction costs not only effectively controls the generation of waste materials on the construction site (including the perceived loss of stirrups made by workers on site), but also reduces the on-site processing volume of workers, saves electricity consumption on the construction site, and greatly reduces production costs. And our company’s product price saves about 30% of the cost compared to the iron horse stool made of waste steel bars on the construction site, and about 50% of the cost compared to the stirrup made of finished steel bars, directly reducing construction costs.